RC0603FR-0710KL
Yageo · Resistors · 0603 · SMD
Profile rc0603fr-0710kl Profiled: 04 Sep 2026
Lifecycle: Active
Availability risk: Low
Specification
Transcribed from the manufacturer datasheet
| Resistance | 10 kΩ |
|---|---|
| Rated power | 0.1 W at 70 °C, derate to 0 at 155 °C |
| Element | Thick film, Ruthenium oxide |
| Temp. coefficient | ±100 ppm/°C (F grade) |
| Working voltage | 50 V (max 75 V overload) |
| Operating range | -55 °C to +155 °C |
| Tolerance | ±1 % |
| Voltage rating | 50 V |
| Lifecycle | Active |
| Datasheet reference | Yageo RC series datasheet, rev. 2024-04, Table 4 (power derating curve) and Table 7 (part number decode) |
|---|---|
| Manufacturer | Yageo |
| Mounting | SMD |
Substitute graph
3 Alternates
Interchangeable part numbers for this profile. A solid node is already profiled in this catalogue; a hollow node is a valid substitute that has no profile yet.
-
RK73H1JTTD1002F not yet profiled
KOA equivalent, same 0603 1 % 10 kΩ. Anti-sulfur construction is better for humid or sulfur-bearing environments; price runs 20-40 % higher.
-
ERJ-3EKF1002V not yet profiled
Panasonic drop-in. Available in tighter ±0.5 % grades from the same series, which lets you tighten a divider without changing pads.
-
AC0603FR-0710KL not yet profiled
Yageo automotive AEC-Q200 variant. Only worth the premium if your build actually needs the qualification paperwork.
Selection notes
The only prose on this page
Where 10 kΩ 0603 actually gets used
Pull-ups on I2C lines (4.7 kΩ-10 kΩ at 3.3 V), gate pull-downs on MOSFETs, divider legs for ADC scaling, and base bias in small-signal stages. At 3.3 V across the body a 10 kΩ part dissipates 1.1 mW, roughly 1 % of rated power, so self-heating is a non-issue in signal paths and the ±100 ppm/°C drift barely moves a divider.
Tolerance and drift in a divider
In a two-resistor divider the ratio error is the difference of the two drifts, not the sum. Two F-grade parts from the same reel track within about ±25 ppm/°C of each other on a short board, so a 1 % divider stays inside about 1.3 % over a 60 °C swing. If you need better than that, either buy a matched array or calibrate at assembly temperature.
Handling and rework
0603 is comfortable for hand soldering with a 0.4 mm tip at 320 °C, but the end terminations dissolve measurably in lead-free solder after about three rework cycles. One rework pass is safe; if a part has been touched twice, replace it rather than reflow it a third time.
Sources
Vishay — https://www.vishay.com/docs/20035/dcrcwe3.pdf · Universidad Nacional de La Plata — https://sedici.unlp.edu.ar/bitstream/handle/10915/162470/Documento_completo.%201a.%20Ed.%20-%20Barbero,%20Issouribehere%20y%20Leibovich.pdf-PDFA.pdf?sequence=1 · NIST — https://www.nist.gov/standardsgov/compliance-faqs-rohs
| Sourcing — Availability risk | One of the highest-volume 0603 values in distribution; multi-million piece stock at Digi-Key, Mouser, LCSC and TME most weeks. Reel pricing lands near $0.004-0.008 each at 5k quantity. The only realistic shortage risk is a broad thick-film allocation event, not this specific value. |
|---|---|
| Pinout and handling | Two-terminal chip; terminals are not polarity sensitive. The printed resistance code sits on the top face and is unreadable once the part is placed on a dense board, so orientation marks come from the pick-and-place nozzle, not the body. |
Engineering information only. Verify every substitution against the manufacturer datasheet and your own operating conditions before committing a design. No pricing or vendor links appear on this page.